Skip to main content

Rotating Propeller: Static Thrust

In this tutorial you simulate a propeller spinning in still air, like a drone in hover, and see the thrust it produces. You set the air properties and the hover inflow, run the case, inspect the flow and the blade surfaces, and finish in the performance report.

This is the Static thrust condition of the Rotating Propeller card. Its guide card is titled Static Wind Propeller. For a propeller with incoming air, see Rotating Propeller: Forward Flight.

Duration: 20 min. Sample model: a prepared two-blade propeller, already imported.

Rotating Propeller card with Static thrust selected

How the tutorial works​

Open Tutorials in the dashboard, choose Rotating Propeller, and select Static thrust under Which condition do you want to simulate? A guide card walks you through the stages Geometry, Model, Physics, Solve, Results, and Report.

  • A page's tasks tick themselves off when you do them. Next unlocks once all of them are done.
  • Only the controls the current task needs respond to clicks.
  • Click a task to see where it is on screen.
A tutorial Run opens a prepared result

Run Simulation in a tutorial submits no job. After about 3 seconds it opens a result computed in advance. In your own projects, the solver creates the mesh and computes the flow, and the values follow your inputs.

Geometry​

Geometry Panel​

The Geometry panel holds the 3D model. Here you can look at its parts, show or hide them, and enter information about the geometry.

  1. Change Model Visibility: toggle the eye icon to hide the model, then show it again.
  2. Try Rotating: drag in the 3D viewport to rotate the model.
  3. Click Next in the guide card.

Geometry Panel page with the propeller in the viewport

Model​

Model Panel​

A spinning propeller is simulated with two cylinders of fluid. This page has nothing to set: look over Define Fluid & Rotating Zone and click Next. The zone sizes stay at their defaults, 1.3 for Inner Radius / Propeller Radius and 0.5 for Inner Height / Propeller Radius.

  • Rotating zone: a small cylinder around the blades. The fluid inside it rotates together with the propeller.
  • Fluid zone: a much larger cylinder around everything. It gives the air room to flow in and the wake room to develop.

Model Panel page showing the fluid and rotating zones

Air Properties​

The fluid properties decide how dense and how viscous the air is, which changes the thrust. Temperature sets both. Warm air is thinner, so the same propeller produces a little less thrust.

  1. Select the Air Preset: click Air under Fluid Properties. Density and viscosity fill in automatically.
  2. Set the Temperature to 24 °C: in Temperature, type 24 and press Enter. Keep the unit on Celsius.
  3. Click Next.

Air Properties page with Air selected and the temperature at 24 °C

Physics​

Static Thrust​

Static thrust is the thrust a propeller makes in still air.

  1. Select Hover: under Inflow, click Hover. The wind speed is fixed at 0 m/s and only the propeller spins.
  2. Set the Angle of Attack to 10°: the rotor angle of attack tilts the propeller disc. In AoA, type 10 and press Enter.
  3. Direction (CCW) and Rotation Speed (1000 rpm) stay at their defaults.
  4. Click Next.

Static Thrust page with Hover selected and AoA 10°

Solve​

Solve Panel · Accuracy​

Accuracy controls how finely the mesh divides the space into cells. Higher levels take more time and credits. Mesh Settings stays on Auto · accuracy-based.

  1. Set Accuracy to 3: move the Accuracy slider to 3, a good balance of precision and cost for this case.
  2. Click Next.

Accuracy slider set to 3

Solve Panel · Acceleration​

Simulation Acceleration adds computing power. The run finishes sooner but uses credits faster. It changes only the speed, not the quality of the results.

  1. Set Simulation Acceleration to 2x: move the slider to 2x.
  2. Click Next.

Guide card asking for Simulation Acceleration 2x

Run Simulation​

Click Run Simulation at the bottom of the Solve panel. If geometry data is still being prepared, wait for the button to become available.

Run Simulation page

Simulation Process​

Wait for the Simulation to Finish. In a tutorial this takes about 3 seconds, and then the prepared result opens by itself.

In your own projects the run has two phases. Mesh splits the simulation space into small cells, and Analysis calculates the flow on them. Click Residuals in the status bar to open the chart: residuals are the calculation error still left, and when the lines go down and flatten, the solution has converged.

Simulation Process page

Results​

Your Results​

The Results panel opens on the velocity magnitude over the whole fluid domain. Click Next.

Your Results page with velocity magnitude over the fluid domain

Result Fields​

Each item in the side panel is a field. Clicking one colours the result by its values, and the colour bar shows which colour means which value.

  1. Check the Y Component of Velocity: in Result Fields, click the Y component on the Velocity row, because the flow direction is Y.
  2. Click Next.

Result Fields with the Y component of Velocity selected

Cut Section​

The Cut tool slices through the result, so you can see the values inside the flow. Saving a cut keeps it under Derived Results, where you can view it together with other results.

  1. Press the Cut Tool: under Visualization Tools, press Cut (Section Slice) in the Section View row. Its settings open beside the panel.
  2. Cut Along X: choose X as the axis, to see how the results are distributed along the flow direction.
  3. Click Save Section: this saves the cut under Derived Results as Cut X 0.50.
  4. Close the Cut Settings with ✕: closing them turns the tool off. The adjusting plane goes away and only the saved cut is left.
  5. Click Next.

Cut settings open with axis X

Camera View​

Set the Camera View to -X: open Camera View in the toolbar above the viewport and choose -X, so you face the cut straight on. Then click Next.

Camera View menu open in the toolbar

View the Cut Together with the Body​

A fluid result comes in two ways. Result shows everything, including the fluid around the propeller. Body (Surface) shows only the surface of your geometry. A derived result, such as your cut, can be selected as well.

  1. Click Body (Surface): the fluid domain goes away and only the propeller surface stays.
  2. Click the Cut: click the cut's name under Derived Results. The cut is now selected, so the next field you choose shows on it.
  3. Click Next.

Propeller surface together with the saved cut

View Turbulence on the Cut​

Fields apply to whatever is selected.

  1. Click Turbulence (μₜ): the cut shows how the flow changes as it passes the propeller.
  2. Click Next.

Turbulence on the cut around the propeller

Prepare the Flow View​

Before moving on, make the body the active result.

  1. Hide the Cut: click the eye on the cut's row.
  2. Click Body (Surface) Again: the body becomes the active result and the view turns to the Z direction.
  3. Click Next.

Body surface selected and the cut hidden

Flow and Pressure Distribution​

On the body surface you can see the pressure distribution. When one side of each blade has high pressure and the other low, the propeller creates thrust.

  1. Click Pressure: compare the colours on the two sides of a blade. The view stays on Z, where the blades are seen edge-on, so rotate it to see the faces. The figure looks along the Y axis. Scroll the mouse wheel over the viewport to zoom in.
  2. Click Next.

Pressure on the blade faces

Streamline Animation​

Streamlines follow the path of the air, so you can see how the flow moves around the propeller.

  1. Turn On the Streamline Tool: under Visualization Tools, switch on Streamline. Its settings open right away.
  2. Play the Animation: choose Lines or Arrows, then press Play in the Animation row.
  3. Click Next.

Streamline settings beside the propeller

Report​

Open the Report: a report is generated for every simulation and collects the key numbers in one place. Click Go to Report at the bottom of the panel.

Streamlines through the propeller with the Report page of the guide card

Report​

Click Next to step through the sections. The last page has Finish instead of Next, and pressing it completes the tutorial.

Core Performance Metrics​

These numbers describe the propeller regardless of its size. Operating State says what the rotor is doing: pushing, braking, or being turned by the flow.

ValueResult
Thrust Coefficient (CT)4.15 × 10⁻²
Torque Coefficient (CQ)4.11 × 10⁻³
Power Coefficient (CP)2.58 × 10⁻²
Operating StatePropulsive

Propulsive means the rotor pushes along the thrust direction and the shaft drives it.

Core Performance Metrics section of the report

Performance Summary​

This is the same performance in real units. Thrust is the force along the thrust direction. Shaft Torque and Shaft Power are what the motor must deliver to keep the propeller turning at this RPM.

ValueResult
Thrust0.05 N
Shaft Torque0.0014 N·m
Shaft Power0.14 W
Rotation DirectionCounter-Clockwise
Rotation Axis / Thrust Direction+Y
Figure of Merit0.261
Disk Loading1.10 Pa
InflowHover
Rotational Speed1000 RPM
AoA10°
Fluid Density1.188 kg/m³
Propeller Diameter / Radius0.251 m / 0.126 m

Performance for This Inflow adds what fits the run. In hover that is the figure of merit and the disk loading.

Performance Summary section of the report

Force and Moment Distribution​

These charts show the final forces and moments on the propeller at iteration 1000. Pressure force comes from the air pushing on the blades. Viscous force comes from the air rubbing along the blades, like friction. The bar charts show in which direction each force and moment is highest.

Final forces and moments distribution

Convergence Graph​

These graphs show how the forces and moments changed while the simulation ran. The values move a lot at the start, and in a good simulation they settle so the lines become almost flat, as they do here.

Press Finish to complete the tutorial.

Iteration history graphs of the forces and moments


Need Assistance or Have Questions?

Frequently Asked Questions: FAQ Link

Support Inquiries: support@everysim.io