Theoretical Background
This page provides the theoretical foundation for the three simulation methods available in Advanced Simulation: Structural Analysis (FEA), Fluid Dynamics (CFD) and Rapid Aerodynamics (Vortex Lattice).
Understanding the underlying theory helps you set up simulations correctly, interpret results with confidence, and recognize the limitations of each method.
1. Structural Analysis — Finite Element Method (FEM)
1.1. Overview
Structural Analysis in EverySim is based on the Finite Element Method (FEM), a numerical technique for solving partial differential equations over complex geometries. The solver is Code_Aster, the mesh uses tetrahedral elements, and parts of an unmerged model are connected with bonded contact.
The core idea is to subdivide the structure into a finite number of small elements (the mesh) and solve the governing equations over each element. The solutions at element boundaries are constrained to be compatible (continuous), and the global solution is assembled from the local element solutions.
1.2. Governing Equation
Under static loading conditions, the equilibrium of a linear elastic solid is governed by:
where:
- — global stiffness matrix, assembled from element stiffness matrices
- — displacement vector (the unknowns to be solved)
- — external force vector (applied loads and boundary conditions)
Each element's stiffness matrix is derived from the element's geometry and material properties:
where is the strain-displacement matrix and is the material constitutive matrix (relating stress to strain via the material's Young's modulus and Poisson's ratio).
1.3. Stress and Strain
Once displacements are obtained, strains and stresses in each element are computed from its nodal displacements :
The von Mises stress is commonly used to assess whether a material is at risk of yielding:
where are the principal stresses.
1.4. Modal and Transient Analysis
EveryStructure also offers Modal Analysis and Transient Structural. EveryDrone project setup offers static analysis only.
Modal analysis solves the eigenvalue problem for the natural frequencies and mode shapes , where is the mass matrix:
Transient analysis integrates the equation of motion over time, with Rayleigh damping set by the coefficients and :
1.5. Assumptions and Limitations
| Assumption | Description |
|---|---|
| Linear elasticity | Material deformation is proportional to applied load (Hooke's Law). Valid when stresses remain below the yield strength. |
| Small deformation | Geometry changes due to deformation are negligible. Not valid for large-deflection problems. |
| Static loading | Applies to Static Structural only: inertial (dynamic) effects are not considered. Suitable for steady-state load cases. |
| Isotropic material | Material properties are identical in all directions. Composite or anisotropic materials are not supported. |
2. Fluid Dynamics — Reynolds-Averaged Navier-Stokes (RANS)
2.1. Overview
Fluid Dynamics simulations in EverySim solve the Reynolds-Averaged Navier-Stokes (RANS) equations, which describe the mean behavior of a turbulent fluid flow, with OpenFOAM SIMPLE-based templates. RANS is the industry-standard approach for external aerodynamics and is computationally tractable for engineering-scale problems.
2.2. Governing Equations
The steady RANS equations for incompressible flow, with constant density , are expressed in three-dimensional integral form as follows. Here, denotes an arbitrary control volume, its bounding surface, and the outward unit normal vector of the surface.
Continuity (mass conservation):
The net volume flux through the bounding surface is zero.
Momentum conservation:
where the viscous stress tensor for a Newtonian fluid is:
where:
- — time-averaged velocity vector (3D)
- — time-averaged pressure
- — fluid density
- — dynamic viscosity (, where is the kinematic viscosity)
- — Reynolds stress tensor, representing the effect of turbulent fluctuations
- — viscous stress tensor
- — tensor product (dyadic product)
2.3. Turbulence Closure
The RANS equations introduce the Reynolds stress tensor as an unknown, so a turbulence model is required to close the system. External flow defaults to -, and rotating flow (MRF) uses - SST.
2.4. Rotating Flow
Rotating flow uses the steady Multiple Reference Frame (MRF) approach: the rotating zone is solved in a rotating frame, without moving the mesh.
2.5. Assumptions and Limitations
| Assumption | Description |
|---|---|
| Steady-state | Time-averaged flow; unsteady effects (e.g., vortex shedding) are not captured. |
| Incompressible flow | Valid for Mach numbers below approximately 0.3. The app cautions above Mach 0.3 and warns above Mach 0.4. Not suitable for transonic or supersonic flows. |
| RANS turbulence model | Mean-flow solution only. Cannot resolve turbulent structures directly (unlike LES or DNS). |
| Merged geometry | Merge multiple bodies in CAD before importing. Rotating flow can add a separate Stationary Body. |
3. Rapid Aerodynamics: Vortex Lattice Method
3.1. Overview
The method behind Rapid Aerodynamics is the Vortex Lattice Method (VLM). It represents lifting surfaces with vortex elements and is an inviscid, potential-flow-based solver. It is well-suited for unsteady aerodynamic analysis of lifting surfaces such as propellers and wings. Source and doublet panel methods are a different formulation.
3.2. Governing Equation — Potential Flow
The Vortex Lattice Method is based on the assumption of incompressible, irrotational, inviscid flow, for which the velocity field can be expressed as the gradient of a scalar potential :
Substituting into the continuity equation yields Laplace's equation:
This is a linear equation and can be solved via superposition of elementary solutions (sources, doublets, and vortices).
3.3. Vortex Panels
The surface of the geometry is discretized into panels. In the standard VLM formulation, each panel carries a closed vortex ring of unknown strength . The boundary condition enforced is the no-penetration condition: the normal component of the total velocity relative to the surface is zero at each panel's control point. For a blade rotating at angular velocity , the surface itself moves at :
This yields a linear system of equations for the vortex strengths , with the known velocities on the right-hand side:
where is the aerodynamic influence coefficient representing the normal velocity induced at panel by a unit vortex on panel . For a fixed wing, is zero.
3.4. Wake Shedding
For unsteady analysis (e.g., rotating propellers), trailing-edge vortices are shed into the wake at each time step. The wake evolves over time, capturing the effect of vorticity on the aerodynamic loads. This allows effective prediction of time-varying thrust and torque of propellers. Runs with a body only and no rotor are steady.
With Enable VPM (Standard mode or higher), the far wake is converted to vortex particles, so it is tracked without extending the wake lattice, at some extra computation.
3.5. Force Computation — Kutta-Joukowski Theorem
The steady force on each bound vortex segment follows from the Kutta-Joukowski theorem:
where is the bound vortex segment vector and is the local velocity, including the velocity induced by the wake. In unsteady potential-flow theory, a time-varying circulation adds a pressure term proportional to .
3.6. Assumptions and Limitations
| Assumption | Description |
|---|---|
| Inviscid flow | The potential-flow model does not resolve viscous effects such as skin friction and boundary layer separation. Treat drag values accordingly. |
| Potential flow | No turbulence; flow must be attached. Results become unreliable at high angles of attack where separation occurs. |
| Thin lifting surfaces | Most accurate for slender wings and propeller blades. Less accurate for thick or bluff bodies. |
4. Method Comparison
| FEA | CFD (RANS) | Rapid Aerodynamics (VLM) | |
|---|---|---|---|
| Physics | Solid mechanics | Viscous turbulent flow | Inviscid potential flow |
| Speed | Fast | Slow | Very fast |
| Accuracy | High (within linear elastic range) | High (attached flow) | Moderate (attached flow only) |
| Unsteady | Static: no; Transient: yes | No (steady RANS) | Yes with rotors; body-only runs are steady |
| Viscous drag | N/A | Yes | Not resolved by the potential-flow model |
| Use case | Stress, deformation | Lift, drag, pressure | Unsteady thrust, torque |
Need Assistance or Have Questions?
Frequently Asked Questions: FAQ Link
Support Inquiries: support@everysim.io